Start with the online Guitar Tuner
Put your guitar in playing position before you begin. Resting the neck on a table or leaning on the bridge can change the pitch you hear. Choose your target in Tuning, check the Microphone selector, then press Start tuning. Your browser will ask permission to use an audio input. Allow it only when you are ready to play. The page analyzes that input locally; it does not record a performance or upload the sound. No account is required for the tuner, and there is no audio file to prepare.
Pluck one open string with a moderate attack, mute the other five, and let the note settle. Turn the appropriate tuning peg a little, then pluck again. Check which string the display has selected before tightening anything. If the note is too low, increase tension carefully; if it is too high, loosen it. A sudden large change is a reason to stop and check the string and tuning, not an instruction to keep winding. Never force a stiff peg or a string that already feels unusually tight.
Read notes, octaves and cents together
The large note name identifies the selected target, while the frequency shows the detected sound in hertz. Standard tuning runs from the thick sixth string to the thin first string: E2, A2, D3, G3, B3, E4. Their targets are approximately 82.4, 110.0, 146.8, 196.0, 246.9 and 329.6 Hz. Both outside strings are E, but they are two octaves apart. A letter alone is therefore not enough to decide that a string is correct. Compare its number and octave as well.
Cents describe pitch difference rather than volume. A negative value means below the target; a positive value means above it. There are 100 cents in a semitone. The green indication uses a window of five cents on either side, which is a display tolerance rather than a guarantee of physical measurement accuracy. Small movement after the attack is normal. Aim for a repeatable reading in the sustained part of the note instead of chasing every brief needle movement as the string vibrates.
Automatic matching or a selected string
Auto-detect follows the nearest plausible target in the selected tuning. It is convenient for moving across a guitar that is already roughly tuned. If the reading switches between strings, click the numbered card for the string you are working on. This locks the comparison to that target. A very large offset while locked can mean that you played the wrong string, selected the wrong card, or the input contains a harmonic. The tool does not silently treat every octave as the same note.
If a guitar is far out of tune, automatic matching may not show a useful target. Choose the string yourself and listen to its reference tone before making a small adjustment. Muting neighboring strings also helps when sympathetic vibration produces a second pitch. After the locked string is stable, choose Auto-detect to return to automatic selection. You can use either approach within the same session; locking is a comparison aid, not a different sound-processing mode or an instruction to retune every string.
Choose an alternate tuning before turning the pegs
The menu includes Standard, Drop D, DADGAD, Drop C, Drop B, Drop A, Open D, Open G, Open E, E-flat Standard and D Standard. Selecting a preset changes the six target notes; it does not change the sound of your instrument. For Drop D, for example, the sixth string target becomes D2 while the remaining five stay at their standard notes. D Standard lowers every string by a whole step, so it is a different setup from lowering only the sixth string.
Check string gauge, instrument setup and the intended tuning before trying a large change. Very low tunings may leave unsuitable strings slack, while some open tunings raise tension on particular strings. The menu is not a safety assessment of your guitar. If unsure, ask a guitar technician rather than tightening until a target appears. The reference is fixed at A4 = 440 Hz. There is no calibration control for a different concert pitch, and this page is designed around six-string guitar targets rather than arbitrary custom instruments.
Use reference tones without confusing them with a reading
Each string card has a Play tone button. It produces a short synthesized reference for the chosen target, useful when you prefer to compare by ear or cannot use a microphone. Listen, let the tone finish, then pluck your string. When two nearby pitches sound together, the pulsing or beating slows as they approach one another. Match the octave first: a similar note name in another register can be misleading, especially when comparing the lowest and highest E strings.
Reference playback and microphone listening do not run together. Starting a reference stops the microphone session; start listening again when you want a measured comparison. A displayed reference frequency tells you what the page is playing, not whether your guitar has reached it. These tones are generated in the browser rather than recordings of a particular acoustic guitar. They are pitch references, so differences in timbre between the tone and your instrument do not mean the pitch is necessarily wrong.
Get a usable input on acoustic or electric guitar
For an acoustic guitar, place the microphone where the open string is clearly audible without touching the body. Avoid a loud backing track, fan noise or another instrument playing nearby. For an electric guitar, a quiet clean amplifier may help a laptop microphone hear the string; heavy distortion, chorus and delay can make a single pitch harder to isolate. An audio interface can be used if the browser exposes its signal as a microphone input. The page cannot directly control an interface driver or its gain.
If access is denied, check the browser's site permissions and the operating system's microphone settings. If the input disappears, reconnect it and select the device again. Microphone access requires HTTPS or localhost and a supporting browser. Stop releases the listening session; switching away from the page also stops its audio. Finally, recheck all six strings after a tuning change, because changing tension on one string can affect the others. If open strings settle but fretted chords remain wrong, string condition, playing pressure or intonation may need attention beyond this tuner.
Guitar tuning questions
Why does the tuner show E2 on one string and E4 on another?
Both are E notes, but E2 is the thick sixth string and E4 is the thin first string. Check the string number and octave together. Do not tighten the low E string to reach E4.
Can I switch to Drop D while the microphone is running?
Yes. Choose Drop D in Tuning and the microphone keeps listening. The sixth-string target changes to D2 and any manual string selection clears. Lower that string carefully; the other five targets stay the same.
Should I tune with my capo on?
For standard open-string tuning, take the capo off first. A capo raises the sounding notes, while the Standard preset still expects E2, A2, D3, G3, B3 and E4. There is no capo transposition setting.
Why did listening stop when I played a reference tone?
Reference playback stops microphone analysis so the generated tone is not treated as your guitar. When you finish comparing by ear, press Start tuning to measure the string again.
Does a green reading mean my guitar will be in tune everywhere?
It means the detected open-string pitch is within the display’s five-cent window. Fretted notes also depend on intonation, string condition and finger pressure. Check these if chords still sound wrong.
Tools for the rest of your practice
Tap a rhythm to estimate the tempo for your next practice exercise.
Analyze a track's key and tempo before practicing along.
Explore note transcription from a recording after tuning your instrument.