Find the note you’re singing right now
Open the Microphone tab, choose Start listening, and allow the browser to use your microphone. Sing a single steady vowel or play one sustained note on an instrument. Wait for the initial breath or attack to pass, then read the note name and frequency. A short phrase is fine as long as the notes sound one at a time. If you just want to check where you landed after a jump, hold the second note for a moment rather than cutting it off as soon as you reach it. Select Stop before switching to a recording.
For vocal practice, begin with a comfortable middle note rather than testing the limits of your voice. Try singing the same note twice, once after hearing a reference from a piano and once without hearing it again. Compare where the note settles, not which attempt produces the smallest number for an instant. Keep the backing track out of the microphone: a loud guide tone may be easier for the detector to pick up than your singing. Use headphones for the reference, pause it before singing, and avoid moving the microphone between attempts.
Read the note, frequency and cents separately
The letter tells you the nearest chromatic note and the number identifies its octave. A3 and A4 share a letter but not a pitch: with the tool’s A4 reference set to 440 Hz, A3 is 220 Hz. That difference matters when you are checking a melody by ear or moving a phrase to a different register. A frequency in hertz counts cycles per second. It is not a measure of loudness, so singing more strongly does not necessarily raise the number. Check the octave first whenever a reading sounds implausible.
The cents display measures distance from the nearest note, not from a note you intended to sing. One semitone contains 100 cents. A negative result sits below the displayed note and a positive result sits above it. An F4 close to zero can still be the wrong result if your target was E4. Also, when the estimated pitch crosses the midpoint between two notes, the displayed note changes and the cents value switches to the other side of the scale. That change can look abrupt even when the underlying pitch is sliding smoothly.
Find a note in a recording without uploading it
Switch to Audio file and use Choose audio to open a recording stored on your device. The browser opens and analyzes it locally. Files can be up to 20 MB and ten minutes long; the browser must be able to decode the format. The first pass analyzes the first 30 seconds, or the entire recording if it is shorter. To inspect a phrase farther in, set Start and End around that passage and select Analyze clip. Each selection can cover up to 60 seconds. Moving the boundaries by itself is not a substitute for analyzing the new selection.
If you have no recording handy, try the built-in sample. It goes through the same analysis as a selected file, so you can practice selecting an excerpt and locating a note on the curve without granting microphone access. With your own recording, start with an isolated note if you are unsure how to read the plot. Then choose a short sequence with a clear pause between notes. These simple checks make it easier to tell a real silence from a gap where the software could not identify a reliable pitch.
Inspect the moment where a phrase changes
Play the analyzed excerpt and listen for the syllable or instrumental attack you want to check. Click the curve or move the playback position to examine that moment. Compare the beginning of a note with its sustained middle. A singer might approach the note from below and settle on it later; a guitarist might bend a string upward before releasing it. The trace lets you separate these deliberate movements from a note that stays consistently above or below the intended target. The point under the cursor describes that moment, not the whole phrase.
A regular ripple around a center can be vibrato. A slope across several neighboring notes can be a slide. Neither pattern automatically means that a performance needs correction. If the line is interrupted, listen around the gap: a consonant, breath, quiet tail or instrumental noise may not contain a sufficiently clear pitch. Do not read gaps as the lowest note. For a useful practice comparison, inspect the same words in two takes, keep the listening position consistent, and compare the sustained parts before worrying about the onset.
Use the detected low and high notes in context
A file analysis reports the lowest and highest sustained notes detected in the selected excerpt. It is a summary of what the tool heard there, not a test of the full range you can sing. Very brief spikes are excluded from the summary, and notes the detector cannot hear clearly may be absent. If an extreme seems suspicious, go to that part of the trace and listen to the original sound. A loud overtone or a second instrument can produce an estimate that does not match the note you meant to measure.
If you are choosing a comfortable key for practice, check a complete phrase rather than deciding from the single highest note alone. Notice where the melody spends most of its time, where you need to breathe, and whether repeating the phrase feels natural. A recording can show that you touched a note once without showing whether you can sustain it comfortably. This tool measures pitch, not vocal strain, register boundaries or voice type. It cannot decide what key suits a singer simply from the minimum and maximum it reports.
Get a cleaner signal when the reading jumps
The pitch finder is meant for one sounding voice or instrument, within approximately 50 to 2000 Hz. Move away from fans or other players, mute resonating strings, and try a steady note. With a microphone, check site permissions and make sure the operating system is using the input you expect. With a file that fails to open, try a short WAV or MP3 export rather than renaming the extension. If a full mix confuses the detector, separate the vocal and analyze that track. For the key or tempo of the full song, use the separate key and BPM tool instead.
Pitch Detector FAQ
Can I use it without a microphone?
Yes. Open Audio file to choose a recording from your device or try the built-in sample. File analysis does not need microphone permission.
How do I check a note after the first 30 seconds?
Move the clip’s start and end to include the note, keep the selection within 60 seconds, and analyze that excerpt again. Then click the trace around the time you want to inspect.
Can it identify all the notes in a chord?
No. It estimates a single pitch at a time. For a chord or a dense mix, play the notes separately or analyze an isolated part.
Does this tune or correct my recording?
No. It displays the estimated pitch and plays back the selected audio without correcting it.